***********************************************************************************************
    Release Notes for Vigor2000

    Firmware Version    : v1.08d
    Build Date/Time     : Wed Dec 5 12:56:53.1 2001

    DrayTek Corp.
    Date: 2001/12/05

***********************************************************************************************

    Files Description:

    <<< Firmware >>>
 
        \Firmware\v2k00108.all          --- Lastest released firmware
                                            (v2k00108.bin + v2k00108.web)
        \Firmware\v2k00108.rst          --- Lastest released firmware
                                            (v2k00108.cfg + v2k00108.bin + v2k00108.web)
        \Firmware\v2k00108.bin          --- Lastest released firmware
                                            (router program firmware only)
        \Firmware\v2k00108.cfg          --- The ROM file of factory default settings 
                                            excluding Lan2Lan and IP Filter
        \Firmware\v2k00108.web          --- The ROM file of webpages of Web Configurator

    << Tools >>>

        \Tools\RtTools_2.01.exe		--- This Router Tools should work with v1.07c 
                                            firmware or laster.
        \Tools\VSetup2k.exe             --- Virtual TA Client 1.06 for Win2000
        \Tools\VSetup95.exe             --- Virtual TA Client 1.06 for Win95
        \Tools\VSetup98.exe             --- Virtual TA Client 1.06 for Win98

    Hint for upgrading Firmware:

        1. The file v2k00108.all should be upgraded under the boot loader mode.
           Please use console port (RS-232 with 115200 8n1) to force the router enter
           boot loader mode.
        2. If you don't care the current settings in your Vigor2000 or you want to
           reset the router, you could upgrade v2k00108.rst to resotore settings 
           to be default values. We recommended you upgrade this file, if your 
           router firmware version is older than v1.03.
        3. If you can't connect to console port to force router enter boot loader mode
           to upgrade *.all or *.rst file, please enable TFTP server via Web Configurator
           to upgrade *.bin first and then *.web. Note that you have to wait for 10
           seconds between two upgrading procedures. Finishing all upgrade, please power
           off-on again.  

    Support Models:

        Vigor2000


Release Notes:

        1. [Web Configurator] 
           a. Fixed IE6.0 layout problem.

	           
***********************************************************************************************
***********************************************************************************************
    Release Notes for Vigor2000

    Firmware Version    : v1.08
    Build Date/Time     : Fri Oct 19 16:0:13.54 2001

    DrayTek Corp.
    Date: 2001/10/25

***********************************************************************************************

    Files Description:

    <<< Firmware >>>
 
        \Firmware\v2k00108.all          --- Lastest released firmware
                                            (v2k00108.bin + v2k00108.web)
        \Firmware\v2k00108.rst          --- Lastest released firmware
                                            (v2k00108.cfg + v2k00108.bin + v2k00108.web)
        \Firmware\v2k00108.bin          --- Lastest released firmware
                                            (router program firmware only)
        \Firmware\v2k00108.cfg          --- The ROM file of factory default settings 
                                            excluding Lan2Lan and IP Filter
        \Firmware\v2k00108.web          --- The ROM file of webpages of Web Configurator

    << Tools >>>

        \Tools\RtTools_2.01.exe		--- This Router Tools should work with v1.07c 
                                            firmware or laster.
        \Tools\VSetup2k.exe             --- Virtual TA Client 1.06 for Win2000
        \Tools\VSetup95.exe             --- Virtual TA Client 1.06 for Win95
        \Tools\VSetup98.exe             --- Virtual TA Client 1.06 for Win98

    Hint for upgrading Firmware:

        1. The file v2k00108.all should be upgraded under the boot loader mode.
           Please use console port (RS-232 with 115200 8n1) to force the router enter
           boot loader mode.
        2. If you don't care the current settings in your Vigor2000 or you want to
           reset the router, you could upgrade v2k00108.rst to resotore settings 
           to be default values. We recommended you upgrade this file, if your 
           router firmware version is older than v1.03.
        3. If you can't connect to console port to force router enter boot loader mode
           to upgrade *.all or *.rst file, please enable TFTP server via Web Configurator
           to upgrade *.bin first and then *.web. Note that you have to wait for 10
           seconds between two upgrading procedures. Finishing all upgrade, please power
           off-on again.  

    Support Models:

        Vigor2000


Release Notes:

        1. [Web Configurator] 
           a. Added "Clear" and "Clear All" buttons for DDNS, Open Ports and 
              Call Schedule Profiles.
           b. Improved HTTP daemon against attacks by nimda virus.
           c. Removed "None" option of "Link Type" for "Dialing to a Single ISP" and
              "Call Control and PPP/MP Setup".
           d. Added more heximal records for "Diagnostic Tools" > "Triggered Dial-Out
              Packet Header".
           e. Fixed a bug that all password fields can not use '*' and '+' character. 

        2. [PPPoE]
           Added the DSS over PPPoE function for PPPoE-enabled ADSL access.
 
           Note: DSS stands for Dynamic Service Selection. If the PPPoE-enabled
           ADSL access netowrk supports multiple PPPoE servers for differnet service
           grade, the function can automatically connect your router to correct 
           PPPoE server.

	3. [NAT]
           Fixed a Port Redirection problem.

	4. [ISDN dial-backup]
           Improved the stability of ISDN dial-backup function.

	5. [DDNS]
           Improved DDNS function. If you have any DDNS update problem, you can use
           telnet command "ddns log" to get logs.
	           
***********************************************************************************************
***********************************************************************************************
    Release Notes for Vigor2000

    Firmware Version    : v1.07c
    Build Date/Time     : Fri Sep 7 17:34:49.38 2001

    DrayTek Corp.
    Date: 2001/09/07

***********************************************************************************************

    Files Description:

    <<< Firmware >>>
 
        \Firmware\v2k00107.all          --- Lastest released firmware
                                            (v2k00107.bin + v2k00107.web)
        \Firmware\v2k00107.rst          --- Lastest released firmware
                                            (v2k00107.cfg + v2k00107.bin + v2k00107.web)
        \Firmware\v2k00107.bin          --- Lastest released firmware
                                            (router program firmware only)
        \Firmware\v2k00107.cfg          --- The ROM file of factory default settings 
                                            excluding Lan2Lan and IP Filter
        \Firmware\v2k00107.web          --- The ROM file of webpages of Web Configurator

    << Tools >>>

        \Tools\RtTools_2.01.exe		--- This Router Tools should work with v1.07c firmware.
        \Tools\VSetup2k.exe             --- Virtual TA Client 1.06 for Win2000
        \Tools\VSetup95.exe             --- Virtual TA Client 1.06 for Win95
        \Tools\VSetup98.exe             --- Virtual TA Client 1.06 for Win98

    Hint for upgrading Firmware:

        1. The file v2k00107.all should be upgraded under the boot loader mode.
           Please use console port (RS-232 with 115200 8n1) to force the router enter
           boot loader mode.
        2. If you don't care the current settings in your Vigor2000 or you want to
           reset the router, you could upgrade v2k00107.rst to resotore settings 
           to be default values. We recommended you upgrade this file, if your 
           router firmware version is older than v1.03.
        3. If you can't connect to console port to force router enter boot loader mode
           to upgrade *.all or *.rst file, please enable TFTP server via Web Configurator
           to upgrade *.bin first and then *.web. Note that you have to wait for 10
           seconds between two upgrading procedures. Finishing all upgrade, please power
           off-on again.  

    Support Models:

        Vigor2000


Release Notes:

        1. [Router Tools and Virtual TA Client] 
           After v1.07 firmware, you should use new Router Tools 2.01 version.

        2. [PPP-over-V.110]
           Add PPPoV110 indication on the "Online Status" page.

        3. [Always-On for PPPoE/PPTP]
           Add an "Always-On" setting for PPPoE/PPTP dial-up connection.

        4. [Disable PING from the Internet]
           Add a checkbox under Management Setup to enable/disable PING packets from the
           Internet.
   
        5. [Call Scheduler]
           Change the default settings of schedules to be 2000/01/01.

        6. [RIP control for LAN]
           Add a RIP control for LAN interface under "LAN TCP/IP and DHCP Setup" page. If
           your local networks has many subnets want to share the router to the Internet. 
           Please set "RIP Protocol Control" to be "1st subnet".

        7. [DNS Proxy]
           Improve DNS Proxy for working with RedHat 7.1 Linux.

        8. [DHCP Server]
           Add a Gateway IP Address setting for DHCP server on Web Configurator.

	           
***********************************************************************************************
***********************************************************************************************
    Release Notes for Vigor2000

    Firmware Version    : v1.07
    Build Date/Time     : Fri Jun 22 11:49:27.86 2001

    DrayTek Corp.
    Date: 2001/06/22

***********************************************************************************************

    Files Description:

    <<< Firmware >>>
 
        \Firmware\v2k00107.all          --- Lastest released firmware
                                            (v2k00106.bin + v2k00106.web)
        \Firmware\v2k00107.rst          --- Lastest released firmware
                                            (v2k00106.cfg + v2k00106.bin + v2k00106.web)
        \Firmware\v2k00107.bin          --- Lastest released firmware
                                            (router program firmware only)
        \Firmware\v2k00107.cfg          --- The ROM file of factory default settings 
                                            excluding Lan2Lan and IP Filter
        \Firmware\v2k00107.web          --- The ROM file of webpages of Web Configurator

    << Tools >>>

        \Tools\RtTools_2.01.exe		--- This Router Tools should work with v1.07 firmware.
        \Tools\VSetup2k.exe             --- Virtual TA Client 1.06 for Win2000
        \Tools\VSetup95.exe             --- Virtual TA Client 1.06 for Win95
        \Tools\VSetup98.exe             --- Virtual TA Client 1.06 for Win98

    Hint for upgrading Firmware:

        1. The file v2k00107.all should be upgraded under the boot loader mode.
           Please use console port (RS-232 with 115200 8n1) to force the router enter
           boot loader mode.
        2. If you don't care the current settings in your Vigor2000 or you want to
           reset the router, you could upgrade v2k00107.rst to resotore settings 
           to be default values. We recommended you upgrade this file, if your 
           router firmware version is older than v1.03.
        3. If you can't connect to console port to force router enter boot loader mode
           to upgrade *.all or *.rst file, please enable TFTP server via Web Configurator
           to upgrade *.bin first and then *.web. Note that you have to wait for 10
           seconds between two upgrading procedures. Finishing all upgrade, please power
           off-on again.  

    Release Notes:

        1. [Router Tools and Virtual TA Client] 
           The Router Tools and Virtual TA Client have been updated, you have to uninstall 
           them from your computer first, then install new ones. You will get new release
           in the Tools folder.

           a. The system administrator password has been encrypted between router 
           and Smart Start Wizard.
           b. Fixed a dual-CPUs problem for Virtual TA Clients.

        2. [ISDN interface control]
           Add a ISDN interface control option on Web Configurator to enable or disable 
           ISDN port. You will find the option in "ISDN Setup" of Basic Setup group.

        3. [PPP-over-V.110]
           Support PPP over V.110 protocol for GSM mobile users remote dial-in access.

        4. [MTU setting for WAN]
           Add a Telnet command "wan mtu ..." to set the MTU (Maximum Transmission Unit)
           for the Ethernet WAN interface. You can use this command to configure the
           MTU size for ISDN, PPPoE, PPTP and Static IP modes.

        5. [SNMP Agent]
           Support SNMP (Simple Network Management Protocol) for improving the capabilities
           of network management. You will find SNMP Setup in the "Management Setup" of
           System Management group.

        6. [DDNS function]
           Support DDNS (Dynamic Domain Name System) function. If you are a registered
           user of www.dyndns.org (the provider of DDNS), you can give one or many domain
           names for your active WAN interface using the function.

        7. [Time Client and Call Scheduler]
           Support NTP (Network Time Procotol) client and Call Scheduler function. The
           Call Scheduler funtion provides you to schedule router's WAN connection or 
           LAN-to-LAN connection by your local time. The NTP client setup could be
           found in "Time Setup" of System Management group. The profiles of Call Scheduler
           could be found in "Call Scheduler Setup" of Advanced Setup group. Also you will
           see these profiles could be assigned for Interface Access (ISDN, PPPoE and PPTP)
           and LAN-to-LAN access.

        8. [Online Status]
           Add a System Uptime on the "Online Status" page of web configurator.

	9. [DHCP Server]
           If put zero in the IP Pool Counts, the dynamic IP pool will be disabled. Now you
           can use Telnet command set "srv dhcp fixip" to add or delete static IP pool. This
           static IP pool supports 10 IP addresses.
 
           > srv dhcp fixip ?
           % Valid subcommands are:
           add          clr          del
           
           Under the "srv dhcp fixip" command string, it support three subcommands: "add",
           "clr" and "del".

           > srv dhcp fixip add ?
           % srv dhcp fixip add <IP Addr> <MAC Addr XX-XX-XX-XX-XX-XX> <Host ID>

           The "add" subcommand can add a specific IP address based on host's Ethernet MAC
           address. The Host ID is optional. For example, if you want to specify a IP address
           192.168.1.123 to a specific computer with MAC address 00-50-7F-12-34-56, you can
           try the following command to add.

           > srv dhcp fixip add 192.168.1.123 00-50-7F-12-34-56 vigor

           > srv dhcp fixip del ?
           % srv dhcp fixip del <IP Addr>

           The "del" subcommand can delete a pre-assigned IP address from the static IP pool.
           For example,

           > srv dhcp fixip del 192.168.1.123

           the host 192.168.1.123 will be removed from the static IP pool.

           > srv dhcp fixip clr 

           The "clr" subcommand can clear the static IP pool to default values.

       10. [Verify default Settings]
           A new Telnet command "sys cfg status" can check if the router is working with
           default settings. If yes, you will see the following message.

           > sys cfg status
           Profile version: 0x2    Status: 0 (0x293ab002)

           where Status: 0 (0x293ab002) means the router is default settings.  

        
***********************************************************************************************

***********************************************************************************************
    Release Notes for Vigor2000

    Firmware Version    : v1.06b
    Build Date/Time     : Thu Feb 15 16:36:46.39 2001

    DrayTek Corp.
    Date: 2001/02/16

***********************************************************************************************

    Files Description:

    <<< Firmware >>>
 
        \Firmware\v2k00106.all          --- Lastest released firmware
                                            (v2k00106.bin + v2k00106.web)
        \Firmware\v2k00106.rst          --- Lastest released firmware
                                            (v2k00106.cfg + v2k00106.bin + v2k00106.web)
        \Firmware\v2k00106.bin          --- Lastest released firmware
                                            (router program firmware only)
        \Firmware\v2k00106.cfg          --- The ROM file of factory default settings 
                                            excluding Lan2Lan and IP Filter
        \Firmware\v2k00106.web          --- The ROM file of webpages of Web Configurator

    Hint for upgrading Firmware:

        1. The file v2k00106.all should be upgraded under the boot loader mode.
           Please use console port (RS-232 with 115200 8n1) to force the router enter
           boot loader mode.
        2. If you don't care the current settings in your Vigor2000 or you want to
           reset the router, you should upgrade v2k00106.rst to resotore settings 
           to be default values. We recommended you upgrade this file, if your 
           router firmware version is older than v1.03.
        3. If you can't connect to console port to force router enter boot loader mode
           to upgrade *.all or *.rst file, please enable TFTP server via Web Configurator
           to upgrade *.bin first and then *.web. Note that you have to wait for 10
           seconds between two upgrading procedures. Finishing all upgrade, please power
           off-on again.  

    Release Note:
        1. Fixed a Typing error in ipnatdmz.sht of Web Configurator.
            "Corbg." ---> "Corp."
        2. ISDN dial-in improvement. Sometimes the dial-in will be failed when
           the remote ISDN TA or router to use ML-PPP to dial into Vigor2000.
        3. Fix a problem that Open Ports can not input 65535 port number.
        4. Fix a Clear button problem under "Advanced Setup" > "IP Filter/Firewall Setup"
           > "Edit Filter Set".

        
***********************************************************************************************

***********************************************************************************************
    Release Note for Vigor2000

    Firmware Version    : v1.06a
    Build Date/Time     : Thu Jan 11 16:52:37.15 2001

    DrayTek Corp.
    Date: 2001/01/12

***********************************************************************************************

    Files Description:

    <<< Firmware >>>
 
        \Firmware\v2k00106.all          --- Lastest released firmware
                                            (v2k00106.bin + v2k00106.web)
        \Firmware\v2k00106.rst          --- Lastest released firmware
                                            (v2k00106.cfg + v2k00106.bin + v2k00106.web)
        \Firmware\v2k00106.bin          --- Lastest released firmware
                                            (router program firmware only)
        \Firmware\v2k00106.cfg          --- The ROM file of factory default settings 
                                            excluding Lan2Lan and IP Filter
        \Firmware\v2k00106.web          --- The ROM file of webpages of Web Configurator
	
	\Firmware\v2kfm106a.zip		--- Compressed all files			
    
    <<< Router Tools & Virtual TA Client >>>
 
        \Tools\Windows\RtSetup.exe    	--- Router Tools for all Windwos Platforms 

      	\Tools\Windows\VSetup2k.exe     --- VTA client for Windows 2000

	\Tools\Windows\VSetup95.exe     --- VTA client for Windows 95

	\Tools\Windows\VSetup98.exe     --- VTA client for Windows 98

	\Tools\Mac OS\Vigor2000 Tools Installer.hqx     --- Vigor2000 Tools for Mac OS

    Hint for upgrading Firmware:

        1. The file v2k00106.all should be upgraded under the boot loader mode.
           Please use console port (RS-232 with 115200 8n1) to force the router enter
           boot loader mode.
        2. If you don't care the current settings in your Vigor2000 or you want to
           reset the router, you should upgrade v2k00106.rst to resotore settings 
           to be default values. We recommended you upgrade this file, if your 
           router firmware version is older than v1.03.
        3. If you can't connect to console port to force router enter boot loader mode
           to upgrade *.all or *.rst file, please enable TFTP server via Web Configurator
           to upgrade *.bin first and then *.web. Note that you have to wait for 10
           seconds between two upgrading procedures. Finishing all upgrade, please power
           off-on again.  

    Release Note:

	1. Improve DMZ host function for Mac OS 9.

	2. Add Open Ports function which allow users to open a port range
	   for specific network applications.

	3. Improve NAT engine for FTP protocol pass-thru.

	4. Fix a LAN-to-LAN and ISP access via ISDN simultaneouly problem which
	   when a LAN-to-LAN connection is up the ISP access will be failed.

	5. Improve Web Configurator for more user-friendly with JavaScripts.

	6. Improve Web Configurator for IE 5.5 and Netscape 6.0 browser.

	7. IPSec ESP tunnel mode pass-thru support.

        
***********************************************************************************************

***********************************************************************************************
    Release Note for Vigor2000

    Firmware Version    : v1.06
    Build Date/Time     : Thu Nov 2 16:10:53.64 2000

    DrayTek Corp.
    Date: 2000/11/02

***********************************************************************************************

    Files Description:

    <<< Firmware >>>
 
        \Firmware\v2k00106.all          --- Lastest released firmware
                                            (v2k00106.bin + v2k00106.web)
        \Firmware\v2k00106.rst          --- Lastest released firmware
                                            (v2k00106.cfg + v2k00106.bin + v2k00106.web)
        \Firmware\v2k00106.bin          --- Lastest released firmware
                                            (router program firmware only)
        \Firmware\v2k00106.cfg          --- The ROM file of factory default settings 
                                            excluding Lan2Lan and IP Filter
        \Firmware\v2k00106.web          --- The ROM file of webpages of Web Configurator
	
	\Firmware\v2kfm106.zip		--- Compressed all files			
    
    <<< Router Tools & Virtual TA Client >>>
 
        \Tools\Windows\RtSetup.exe    	--- Router Tools for all Windwos Platforms 

      	\Tools\Windows\VSetup2k.exe     --- VTA client for Windows 2000

	\Tools\Windows\VSetup95.exe     --- VTA client for Windows 95

	\Tools\Windows\VSetup98.exe     --- VTA client for Windows 98

	\Tools\Mac OS\Vigor2000 Tools Installer.hqx     --- Vigor2000 Tools for Mac OS

    Hint for upgrading Firmware:

        1. The file v2k00106.all should be upgraded under the boot loader mode.
           Please use console port (RS-232 with 115200 8n1) to force the router enter
           boot loader mode.
        2. If you don't care the current settings in your Vigor2000 or you want to
           reset the router, you should upgrade v2k00106.rst to resotore settings 
           to be default values. We recommended you upgrade this file, if your 
           router firmware version is older than v1.03.
        3. If you can't connect to console port to force router enter boot loader mode
           to upgrade *.all or *.rst file, please enable TFTP server via Web Configurator
           to upgrade *.bin first and then *.web. Note that you have to wait for 10
           seconds between two upgrading procedures. Finishing all upgrade, please power
           off-on again.  

    Release Note:

        1. PPTP client for few specific PPTP-enabled ADSL modem

        To click "Quick Setup" > "Internet Access Setup" > "PPTP" configures
        PPTP and also can configure the ISDN dial backup settings.

	Note: Before you enable the PPTP client, you should use 2nd IP address to connect
              to the ADSL modem. Please click "Basic Setup" > "Ethernet TCP/IP and DHCP 
              Setup" to enable the 2nd IP address and assign the IP address and subnet mask.

        2. Netmeeting support

        The Netmeeting support is just a beta release. Based on the current release, you 
        just can make a Netmeeting call directly using peer IP address. If you want to peer
        to call into your local Netmeeting software, please add two port redirection entries
        in the "Advanced Setup" > "NAT Setup" > "Configure Port Redirection Table". These
        additional ports is TCP/1720 and TCP/1503. However, the ILS server support should
        be released in the next version.

	3. PPTP Tunnel Passthru

	This version supports any of PPTP clients could create a tunnel through the router to
        establish a secure channel with outside PPTP server.

        4. PPPoE Enhancement

	This version has done some significant performance improvement for T-DSL services
        in Germany. If you are a T-DSL user, please use the version.       

        5. Tools for Windows Platform

	Now, the Windows utility has been separate to two independent installers, 
        one is named "Router Tools" including "Firmware Upgrade Utility" and "Smart Start 
        Wizard", the other is named "Virtual TA" client driver which has been supported for
        Win95 OSR2.1, Win98 and Win2000. The Router Tools can support whole Windows platforms.

	6. LAN-to-LAN Profile bug

	Fixed a bug which the LAN-to-LAN profile settings will be clear to be default
        value after upgrade new firmware.

	7. Call Control Parameters

	Please click "Advanced Setup" > "Call Control and PPP/MP Setup", you will see the
        following two parameters: Dial Retry and Dial Delay Interval. These are globally
        settings for all dial-out mechanism, such as ISDN dialup, PPPoE or PPTP for ADSL
        access. The Dial Retry means the router will dial the preset times per outgoing 
        packet. The Dial Delay Interval means the time interval between two re-dials.

	8. Remote Activation Function

	Please click "Advanced Setup" > "Call Control and PPP/MP Setup", you will see the
        "Remote Activation" field. You should specify the caller phone number here. Once the
        router receives a call from the specified phone or ISDN line number, it is will 
        drop the incoming call immediatelly and then dial to the ISP for the Internet access. 
        If you are a fixed IP user, the router will be wake up remotely, then you could
        access to your local network resource very easy.

	Note: Before you enable the function, you should set a ISP access profile following
              the links "Quick Setup" > "Internet Access Setup" > "Dialling to Single ISP".

	9. Remote Management

	Add a "Allowing management from the Internet" checkbox on the Management Setup page
        of Web Configurator. By default, the checkbox is unchecked. It means the router
        can NOT configure from the Internet.

        
***********************************************************************************************

[End of File]
